PWM.zip_PIC16F_pic16f1619_pic16f1619 pwm_pic24f00pwm_汇编

/** @Generated PIC10 / PIC12 / PIC16 / PIC18 MCUs Source File @Company: Microchip Technology Inc. @File Name: mcc.c @Summary: This is the mcc.c file generated using PIC10 / PIC12 / PIC16 / PIC18 MCUs @Description: This header file provides implementations for driver APIs for all modules selected in the GUI. Generation Information : Product Revision : PIC10 / PIC12 / PIC16 / PIC18 MCUs - 1.65 Device : PIC16F1619 Driver Version : 2.00 The generated drivers are tested against the following: Compiler : XC8 1.45 or later MPLAB : MPLAB X 4.10 */ /* (c) 2016 Microchip Technology Inc. and its subsidiaries. You may use this software and any derivatives exclusively with Microchip products. THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE, INCLUDING ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, OR ITS INTERACTION WITH MICROCHIP PRODUCTS, COMBINATION WITH ANY OTHER PRODUCTS, OR USE IN ANY APPLICATION. IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS SOFTWARE. MICROCHIP PROVIDES THIS SOFTWARE CONDITIONALLY UPON YOUR ACCEPTANCE OF THESE TERMS. */ // Configuration bits: selected in the GUI // CONFIG1 #pragma config FOSC = INTOSC // Oscillator Selection Bits->INTOSC oscillator: I/O function on CLKIN pin #pragma config PWRTE = OFF // Power-up Timer Enable->PWRT disabled #pragma config MCLRE = ON // MCLR Pin Function Select->MCLR/VPP pin function is MCLR #pragma config CP = OFF // Flash Program Memory Code Protection->Program memory code protection is disabled #pragma config BOREN = ON // Brown-out Reset Enable->Brown-out Reset enabled #pragma config CLKOUTEN = OFF // Clock Out Enable->CLKOUT function is disabled. I/O or oscillator function on the CLKOUT pin #pragma config IESO = ON // Internal/External Switch Over->Internal External Switch Over mode is enabled #pragma config FCMEN = ON // Fail-Safe Clock Monitor Enable->Fail-Safe Clock Monitor is enabled // CONFIG2 #pragma config WRT = OFF // Flash Memory Self-Write Protection->Write protection off #pragma config PPS1WAY = ON // Peripheral Pin Select one-way control->The PPSLOCK bit cannot be cleared once it is set by software #pragma config ZCD = OFF // Zero Cross Detect Disable Bit->ZCD disable. ZCD can be enabled by setting the ZCDSEN bit of ZCDCON #pragma config PLLEN = OFF // PLL Enable Bit->4x PLL is enabled when software sets the SPLLEN bit #pragma config STVREN = ON // Stack Overflow/Underflow Reset Enable->Stack Overflow or Underflow will cause a Reset #pragma config BORV = LO // Brown-out Reset Voltage Selection->Brown-out Reset Voltage (Vbor), low trip point selected. #pragma config LPBOR = OFF // Low-Power Brown Out Reset->Low-Power BOR is disabled #pragma config LVP = ON // Low-Voltage Programming Enable->Low-voltage programming enabled // CONFIG3 #pragma config WDTCPS = WDTCPS1F // WDT Period Select->Software Control (WDTPS) #pragma config WDTE = OFF // Watchdog Timer Enable->WDT disabled #pragma config WDTCWS = WDTCWSSW // WDT Window Select->Software WDT window size control (WDTWS bits) #pragma config WDTCCS = SWC // WDT Input Clock Selector->Software control, controlled by WDTCS bits #include "mcc.h" void SYSTEM_Initialize(void) { PIN_MANAGER_Initialize(); OSCILLATOR_Initialize(); PWM1_Initialize(); TMR2_Initialize(); ADC_Initialize(); } void OSCILLATOR_Initialize(void) { // SCS FOSC; SPLLEN disabled; IRCF 500KHz_MF; OSCCON = 0x38; // TUN 0; OSCTUNE = 0x00; // SBOREN disabled; BORFS disabled; BORCON = 0x00; } /** End of File */