How to Use the Tracert Command in Windows

Open Command Prompt and type tracert followed by the destination

By
Tim Fisher
Photo of Tim Fisher, Lifewire GM and Writer
Tim Fisher
Senior Vice President & Group General Manager, Tech & Sustainability
  • Emporia State University
Tim Fisher has more than 30 years' of professional technology experience. He's been writing about tech for more than two decades and serves as the SVP and General Manager of Lifewire.
lifewire's editorial guidelines
Updated on June 25, 2024
Reviewed by
Lisa Mildon
Lisa Mildon
Reviewed by Lisa Mildon
  • Southern New Hampshire University
Lisa Mildon is a Lifewire writer and an IT professional with 30 years of experience. Her writing has appeared in Geekisphere and other publications.
lifewire's editorial guidelines

What to Know

  • The tracert command details the path a packet takes from your computer to the destination you specify.
  • For example, enter tracert google.com into Command Prompt. IP addresses work, too: tracert 192.168.1.1.

This article details how to use the Windows tracert command. It includes all the switches that work with tracert and some examples that show how to write it. You might sometimes see this command referred to as trace route or traceroute; it's all the same command.

Tracert Command Syntax

If you know how to read command syntax, the syntax for tracert is pretty straightforward:

tracert [-d] [-h MaxHops] [-w TimeOut] [-4] [-6] target [/?]

The availability of certain tracert command switches and other tracert command syntax may differ from operating system to operating system. Tracert, as it's explained below, applies to Windows only, but the command is also available for Linux.

The tracert help command in Windows 11 Command Prompt
Tracert Command Options
Option Explanation
-d This option prevents tracert from resolving IP addresses to hostnames, often resulting in much faster results.
-h MaxHops This tracert option specifies the maximum number of hops in the search for the target. If you do not specify MaxHops, and a target has not been found by 30 hops, tracert will stop looking.
-w TimeOut You can specify the time, in milliseconds, to allow each reply before timeout using this tracert option.
-4 This option forces tracert to use IPv4 only.
-6 This option forces tracert to use IPv6 only.
target This is the destination, either an IP address or hostname.
/? Use the help switch with the tracert command to show detailed help about the command's several options.

Other less commonly used options for the tracert command also exist, including [-j HostList], [-R], and [-S SourceAddress]. Use the help switch with the Windows tracert command for more information on these options.

Save the lengthy results of a tracert command by redirecting the command output to a file with a redirection operator.

Tracert Command Examples

Here are some examples of the various ways you might use this command:

Tracert to a Router 

 tracert 192.168.1.1

In the above example, the tracert command is used to show the path from the networked computer on which the tracert command is being executed by a network device, in this case, a router on a local network, that's assigned the 192.168.1.1 IP address.

The result displayed on the screen will look something like this: 

 Tracing route to 192.168.1.1 over a maximum of 30 hops
1 <1 ms <1 ms <1 ms 192.168.1.254
2 <1 ms <1 ms <1 ms 192.168.1.1
Trace complete.

In this example, you can see that tracert found a network device using the IP address of 192.168.1.254, let's say a network switch, followed by the destination, 192.168.1.1, the router.

Tracert to a Website 

 tracert www.google.com

With the tracert command shown above, we're asking tracert to show us the path from the local computer all the way to the network device with the hostname www.google.com. 

 Tracing route to www.l.google.com [209.85.225.104]
over a maximum of 30 hops:
1 <1 ms <1 ms <1 ms 10.1.0.1
2 35 ms 19 ms 29 ms 98.245.140.1
3 11 ms 27 ms 9 ms te-0-3.dnv.comcast.net [68.85.105.201]
...
13 81 ms 76 ms 75 ms 209.85.241.37
14 84 ms 91 ms 87 ms 209.85.248.102
15 76 ms 112 ms 76 ms iy-f104.1e100.net [209.85.225.104]
Trace complete.

In this example, we can see that tracert identified fifteen network devices including our router at 10.1.0.1 and all the way through to the target of www.google.com, which we now know uses the public IP address of 209.85.225.104, one of Google's many IP addresses.

Hops 4 through 12 were excluded above just to keep the example simple. If you were executing a real tracert, those results would all show up on screen.

Tracert Without Resolving Hostnames 

 tracert -d www.yahoo.com

With this tracert command example, we're again requesting the path to a website, this time www.yahoo.com, but now we're preventing tracert from resolving hostnames by using the -d option. 

 Tracing route to any-fp.wa1.b.yahoo.com [209.191.122.70]
over a maximum of 30 hops:
1 <1 ms <1 ms <1 ms 10.1.0.1
2 29 ms 23 ms 20 ms 98.245.140.1
3 9 ms 16 ms 14 ms 68.85.105.201
...
13 98 ms 77 ms 79 ms 209.191.78.131
14 80 ms 88 ms 89 ms 68.142.193.11
15 77 ms 79 ms 78 ms 209.191.122.70
Trace complete.

We can see that tracert again identified fifteen network devices including our router at 10.1.0.1 and through to the target of www.yahoo.com, which we can assume uses the public IP address of 209.191.122.70.

As you can see, tracert didn't resolve any hostnames this time, which significantly sped up the process.

Save Tracert Results to a File 

 tracert -h 3 lifewire.com > z:\tracertresults.txt

In this last example of the tracert command in Windows, we're using -h to limit the hop count to 3, but instead of displaying the results in Command Prompt, we'll use the > redirection operator to send it all to a TXT file located on Z:, an external hard drive.

Here are some example results of this last command: 

 Tracing route to lifewire.com [151.101.66.114]
over a maximum of 3 hops:
1  <1 ms  <1 ms  <1 ms testwifi.here [192.168.86.1]
2   1 ms   1 ms  <1 ms 192.168.1.1
3  17 ms  16 ms  17 ms giantwls-64-71-222-1.giantcomm.net [64.71.222.1]
Trace complete.

Tracert Command Availability

The tracert command is available from within the Command Prompt in all Windows operating systems including Windows 11, Windows 10, Windows 8, Windows 7, Windows Vista, Windows XP, and older versions of Windows as well.

Tracert Related Commands

The tracert command is often used with other networking-related Command Prompt commands like ping, ipconfig, netstat, nslookup, and others. The pathping command is similar to tracert but also shows network latency and loss information.

Was this page helpful?